{"id":502,"date":"2026-09-16T05:48:11","date_gmt":"2026-09-16T05:48:11","guid":{"rendered":"https:\/\/spiralgears.top\/product\/spiral-miter-gear-set\/"},"modified":"2026-09-17T07:59:02","modified_gmt":"2026-09-17T07:59:02","slug":"spiral-miter-gear-set","status":"publish","type":"product","link":"https:\/\/spiralgears.top\/ms\/product\/spiral-miter-gear-set\/","title":{"rendered":"Set Gear Miter Lingkaran"},"content":{"rendered":"
\n

A spiral miter gear set uses equal tooth counts to transmit motion between intersecting shafts without intentionally changing speed ratio. Equal ratio simplifies one part of the selection, but the hand, shaft angle, mounting distance, interfaces and backlash still have to be defined.<\/p>\n

Best starting point:<\/strong> A compact intersecting-axis direction change with approximately 1:1 ratio and a matched spiral bevel pair.<\/p>\n<\/div>\n

\n
\n
\n

What this product family is designed to solve<\/h2>\n

Miter gears are often chosen for packaging and direction change. The gear set should be treated as a matched pair, especially when the assembly is sensitive to contact or lost motion.<\/p>\n

Use a miter set when equal ratio is part of the design. If the ratio is not 1:1, or one member is integrated with a long shaft, use the custom or pinion-shaft product family instead.<\/p>\n<\/div>\n

\"Set<\/figure>\n<\/div>\n<\/section>\n
\n
\n

Specification and RFQ table<\/h2>\n

For spiral miter gear set, exact numerical values are confirmed for the ordered configuration. The table below identifies the drawing and enquiry fields that need explicit control.<\/p>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Selection item<\/th>\nConfiguration<\/th>\nRFQ note<\/th>\n<\/tr>\n<\/thead>\n
Pair identity<\/td>\nMatched spiral bevel gear pair or project-specific single component<\/td>\nConfirm the mating member and driving relationship.<\/td>\n<\/tr>\n
Shaft angle<\/td>\nProject-specific<\/td>\nShow the axis relationship or assembly drawing.<\/td>\n<\/tr>\n
Ratio \/ tooth counts<\/td>\nTo drawing or RFQ<\/td>\nProvide both tooth counts when known.<\/td>\n<\/tr>\n
Module \/ diametral pitch<\/td>\nTo drawing or RFQ<\/td>\nDo not estimate from outside diameter alone.<\/td>\n<\/tr>\n
Pressure angle<\/td>\nConfirm for ordered configuration<\/td>\nUse the drawing or reliable legacy data for replacement work.<\/td>\n<\/tr>\n
Spiral angle & hand<\/td>\nConfirm for ordered configuration<\/td>\nIdentify right\/left hand with a defined viewing convention.<\/td>\n<\/tr>\n
Mounting distance \/ backlash<\/td>\nProject-specific<\/td>\nProvide housing datums and target range when controlled.<\/td>\n<\/tr>\n
Bore \/ spline \/ shaft interface<\/td>\nTo drawing or sample<\/td>\nInclude keyway, spline standard, journals and datum requirements.<\/td>\n<\/tr>\n
Material \/ heat treatment<\/td>\nTo drawing or project review<\/td>\nState mandatory grade, hardness or case requirements if controlled.<\/td>\n<\/tr>\n
Tooth finish \/ quality<\/td>\nTo drawing or project review<\/td>\nState cut\/ground requirement and the acceptance standard or inspection criteria.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n
\n

A 1:1 ratio still needs a defined shaft relationship<\/h2>\n

The drawing should show both members, the shaft angle and the references that locate them. If the gears are integrated into hubs, shafts or flanges, those features must be tied to the tooth datums. Manufacturing and inspection then follow the ordered material and tooth-finish requirements.<\/p>\n

The technical visual for spiral miter gear set is a discussion aid for component relationships. The controlled production drawing and approved quotation remain the dimensional definition for the order.<\/p>\n<\/div>\n

\"A<\/figure>\n<\/div>\n<\/section>\n
\n
\n

Interfaces and assembly checks<\/h2>\n
\n
\"\"<\/p>\n

Mating member<\/h3>\n

Confirm which gear mates with the component and whether both members are included in the supply.<\/p>\n<\/article>\n

\"\"<\/p>\n

Datums & mounting<\/h3>\n

Show the surfaces and axes that control mounting distance, shaft position and backlash.<\/p>\n<\/article>\n

\"\"<\/p>\n

Laluan bahan<\/h3>\n

State controlled material\/heat-treatment requirements and identify features that need secondary machining.<\/p>\n<\/article>\n

\"\"<\/p>\n

Penerimaan<\/h3>\n

List the dimensional, tooth-quality, runout or contact checks that are required for release.<\/p>\n<\/article>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Typical application fit<\/h2>\n

Right-angle auxiliary drives, compact machine mechanisms, automation equipment and gearboxes where equal ratio and intersecting axes are required.<\/p>\n

Application duty should be sent with the drawing whenever it can change the material route, tooth finishing, support assumptions or inspection requirement.<\/p>\n

\"Aplikasi<\/a>

\"\"Alat Mesin CNC<\/a><\/h3>

Pemacu sudut kanan dan mekanisme penentuan kedudukan yang penting dalam hal kekakuan pemasangan dan tindak balas.<\/p>Panduan permohonan \u2192<\/a><\/div><\/article>

\"Aplikasi<\/a>

\"\"Robotik & Automasi<\/a><\/h3>

Mekanisme paksi bersilang yang padat dengan keperluan tugas pembalikan dan kebolehulangan.<\/p>Panduan permohonan \u2192<\/a><\/div><\/article>

\"Aplikasi<\/a>

\"\"Sistem Pemotongan & Gantry Laser<\/a><\/h3>

Penghantaran yang mengubah arah di sekitar gantry dan peralatan kedudukan automatik.<\/p>Panduan permohonan \u2192<\/a><\/div><\/article>

\"Aplikasi<\/a>

\"\"Angkat Berat & Pengangkat<\/a><\/h3>

Mekanisme tugas berat yang memerlukan semakan semula susunan kejutan, permulaan\/hentian dan sokongan.<\/p>Panduan permohonan \u2192<\/a><\/div><\/article>

\"Aplikasi<\/a>

\"\"Jentera Ketepatan<\/a><\/h3>

Sistem ketepatan padat dengan datum terkawal, larian keluar dan keperluan sentuhan.<\/p>Panduan permohonan \u2192<\/a><\/div><\/article>

\"Kotak<\/a>

\"\"Kotak Gear Perindustrian<\/a><\/h3>

Peringkat kotak gear yang menghalakan tork melalui susunan aci yang bersilang.<\/p>Panduan permohonan \u2192<\/a><\/div><\/article><\/div><\/div>\n<\/section>\n

\n
\n

Manufacturing and inspection sequence<\/h2>\n
\n
1<\/strong><\/p>\n

Review<\/h3>\n

Confirm drawing revision, pair identity, open questions and acceptance-critical features.<\/p>\n<\/div>\n

2<\/strong><\/p>\n

Plan<\/h3>\n

Define blank, datum machining, gear cutting, heat treatment and finish sequence.<\/p>\n<\/div>\n

3<\/strong><\/p>\n

Finish<\/h3>\n

Complete tooth and interface finishing according to the ordered route.<\/p>\n<\/div>\n

4<\/strong><\/p>\n

Inspect<\/h3>\n

Check the dimensions and gear-related criteria agreed for the configuration.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

What to include in the enquiry<\/h2>\n
\n\n\n\n\n\n\n\n\n\n
RFQ group<\/th>\nRecommended detail<\/th>\n<\/tr>\n<\/thead>\n
Technical definition<\/td>\nCurrent drawing, pair reference, ratio\/tooth counts, hand and axis relationship<\/td>\n<\/tr>\n
Assembly<\/td>\nBore\/shaft\/spline, bearings, housing datums, mounting distance and backlash if controlled<\/td>\n<\/tr>\n
Kewajipan<\/td>\nSpeed, torque\/load spectrum, reversals, shock, environment and lubrication<\/td>\n<\/tr>\n
Kualiti<\/td>\nMaterial, heat treatment, tooth finish, tolerances and inspection records<\/td>\n<\/tr>\n
Komersial<\/td>\nPrototype and repeat quantity, destination, timing target and preferred trade term<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n

Frequently asked questions<\/h2>\n
\n
\nCan I order only one member of the pair?<\/summary>\n

For spiral miter gear set, supplying one member can be reviewed when the mate is fully defined. If the existing mate is unknown, send its drawing, measurements or physical gear before releasing a single component.<\/p>\n<\/details>\n

\nCan a worn sample be copied directly?<\/summary>\n

A worn spiral miter gear set sample can support identification, but wear should not be treated as original geometry. Legacy drawings, an unused mating member and assembly measurements provide a stronger reconstruction basis.<\/p>\n<\/details>\n

\nDo I need to choose material and heat treatment before the RFQ?<\/summary>\n

When the spiral miter gear set design controls material or heat treatment, state the exact requirement. If those items are open, describe duty and mark them for selection review rather than borrowing a grade from another gear.<\/p>\n<\/details>\n

\nHow are small sample quantities handled?<\/summary>\n

Small samples of spiral miter gear set can be reviewed for suitable new projects. Separate prototype quantity from expected repeat demand so setup, inspection and later production are planned against the correct volume.<\/p>\n<\/details>\n<\/div>\n<\/div>\n<\/section>\n

\n

Perancangan komersial untuk RFQ anda<\/h3>\n

Untuk perancangan permintaan sebut harga, MOQ adalah fleksibel dan bergantung pada bentuk produk, laluan pemprosesan dan nilai pesanan keseluruhan. Projek baharu yang sesuai boleh disemak untuk 1\u20135 sampel barang pada harga sampel. Model yang berbeza boleh digabungkan apabila jumlah pesanan mencapai kira-kira USD 1,500. Pesanan 1\u20132 barang juga boleh dipertimbangkan, biasanya pada kos unit yang lebih tinggi kerana persediaan dan pemeriksaan diagihkan kepada kuantiti yang sangat kecil.<\/p>\n

Untuk permintaan sebut harga, perancangan penghantaran, tempoh masa biasa adalah 10\u201325 hari bekerja untuk alat ganti standard, 20\u201345 hari bekerja untuk komponen tersuai dan 45\u2013120 hari bekerja untuk peralatan atau pemasangan jenis projek. EXW, FOB, CIF dan DAP biasanya disokong; FCA, CFR, CPT, CIP dan DDP boleh dibincangkan untuk penghantaran dan destinasi tertentu.<\/p>\n<\/div>\n

Minta sebut harga<\/span>

Hantar pasangan gear, lukisan dan tugas dalam satu RFQ.<\/h2>

Lebih jelas hubungan pasangan dan datum pemasangan ditakrifkan, lebih cepat konfigurasi dapat disemak.<\/p>

Panduan pesanan & penghantaran<\/h3>

MOQ adalah fleksibel mengikut jenis produk, laluan pembuatan dan jumlah nilai pesanan. Projek baharu yang sesuai boleh meminta 1\u20135 sampel barang pada harga sampel. Model campuran boleh digabungkan apabila jumlah pesanan mencapai kira-kira USD 1,500. Pesanan 1\u20132 barang boleh disemak, walaupun kos seunit biasanya lebih tinggi.<\/p>

Tempoh perancangan biasa ialah 10\u201325 hari bekerja untuk bahagian standard, 20\u201345 hari bekerja untuk komponen tersuai dan 45\u2013120 hari bekerja untuk peralatan atau pemasangan jenis projek. EXW, FOB, CIF dan DAP biasanya disokong; FCA, CFR, CPT, CIP dan DDP boleh dibincangkan untuk penghantaran.<\/p><\/div><\/div>Hantar RFQ<\/a><\/div><\/div><\/section>","protected":false},"excerpt":{"rendered":"

A spiral miter gear set uses equal tooth counts to transmit motion between intersecting shafts without intentionally changing speed ratio. Equal ratio simplifies one part of the selection, but the hand, shaft angle, mounting distance, interfaces and backlash still have to be defined. A compact intersecting-axis direction change with approximately 1:1 ratio and a matched spiral bevel pair.<\/p>","protected":false},"featured_media":470,"comment_status":"open","ping_status":"closed","template":"","meta":[],"product_brand":[],"product_cat":[1594],"product_tag":[],"class_list":["post-502","product","type-product","status-publish","has-post-thumbnail","product_cat-spiral-miter-gear-sets","first","instock","shipping-taxable","product-type-simple"],"_links":{"self":[{"href":"https:\/\/spiralgears.top\/ms\/wp-json\/wp\/v2\/product\/502","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/spiralgears.top\/ms\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/spiralgears.top\/ms\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/spiralgears.top\/ms\/wp-json\/wp\/v2\/comments?post=502"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/spiralgears.top\/ms\/wp-json\/wp\/v2\/media\/470"}],"wp:attachment":[{"href":"https:\/\/spiralgears.top\/ms\/wp-json\/wp\/v2\/media?parent=502"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/spiralgears.top\/ms\/wp-json\/wp\/v2\/product_brand?post=502"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/spiralgears.top\/ms\/wp-json\/wp\/v2\/product_cat?post=502"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/spiralgears.top\/ms\/wp-json\/wp\/v2\/product_tag?post=502"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}