{"id":486,"date":"2026-09-16T05:47:46","date_gmt":"2026-09-16T05:47:46","guid":{"rendered":"https:\/\/spiralgears.top\/manufacturing-quality\/"},"modified":"2026-09-17T07:58:23","modified_gmt":"2026-09-17T07:58:23","slug":"manufacturing-quality","status":"publish","type":"page","link":"https:\/\/spiralgears.top\/fr\/manufacturing-quality\/","title":{"rendered":"Manufacturing & Quality"},"content":{"rendered":"
\n
\n
Manufacturing & quality<\/span><\/p>\n

Manufacturing & Quality for Spiral Bevel Gears<\/h1>\n

The manufacturing route is planned around the controlled drawing and the acceptance method. The aim is to keep blank datums, heat-treatment condition, tooth finishing and final inspection connected rather than treating them as isolated operations.<\/p>\n

Demander un devis<\/a>Parcourir les produits<\/a><\/div>\n<\/div>\n
\"Paire<\/figure>\n<\/div>\n<\/section>\n
\n
\n

Process route<\/h2>\n
\n
1<\/strong><\/p>\n

Drawing & datum review<\/h3>\n

Confirm the gear pair, machining references, interfaces and inspection requirements.<\/p>\n<\/div>\n

2<\/strong><\/p>\n

Blank & machining preparation<\/h3>\n

Plan turning and interface machining so later gear operations have stable references.<\/p>\n<\/div>\n

3<\/strong><\/p>\n

Gear cutting & heat treatment<\/h3>\n

Use the ordered gear system and protect critical surfaces according to the process plan.<\/p>\n<\/div>\n

4<\/strong><\/p>\n

Finishing & inspection<\/h3>\n

Finish teeth where specified, verify drawing characteristics and prepare agreed records.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n
\n

Inspection scope should be agreed before production<\/h2>\n

Not every part needs the same report. A replacement pair may depend on contact, mounting geometry and dimensional comparison with a sample. A drawing-controlled production part may call for a defined gear quality standard, runout, bore or spline checks and material\/heat-treatment records. Put these expectations into the RFQ so they can be included in the route and quotation.<\/p>\n<\/div>\n

\"Inspection<\/figure>\n<\/div>\n<\/section>\n
\n
\n

Typical inspection questions<\/h2>\n
\n
\"\"<\/p>\n

Datum dimensions<\/h3>\n

Which dimensions establish mounting distance, shaft location and the relationship to the tooth geometry?<\/p>\n<\/article>\n

\"\"<\/p>\n

Pair identification<\/h3>\n

Are the mating components controlled as a set, and how must hand or pair marking be managed?<\/p>\n<\/article>\n

\"\"<\/p>\n

Gear quality<\/h3>\n

Which gear-quality or tooth inspection requirement applies to the ordered configuration?<\/p>\n<\/article>\n

\"\"<\/p>\n

Material condition<\/h3>\n

Which material, heat-treatment and hardness requirements are stated on the controlled drawing?<\/p>\n<\/article>\n<\/div>\n<\/div>\n<\/section>\n

Demander un devis<\/span>

Veuillez inclure la paire d'engrenages, le sch\u00e9ma et le descriptif du service dans une seule demande de devis.<\/h2>

Plus les relations d'accouplement et les donn\u00e9es d'assemblage sont d\u00e9finies clairement, plus la configuration peut \u00eatre examin\u00e9e rapidement.<\/p>

Conseils pour les commandes et la livraison<\/h3>

La quantit\u00e9 minimale de commande (MOQ) est flexible et d\u00e9pend du type de produit, du proc\u00e9d\u00e9 de fabrication et du montant total de la commande. Pour les nouveaux projets, il est possible de commander de 1 \u00e0 5 \u00e9chantillons \u00e0 un tarif pr\u00e9f\u00e9rentiel. Diff\u00e9rents mod\u00e8les peuvent \u00eatre combin\u00e9s lorsque le montant total de la commande atteint environ 1\u00a0500\u00a0USD. Les commandes de 1 \u00e0 2\u00a0pi\u00e8ces peuvent \u00eatre \u00e9tudi\u00e9es, bien que le co\u00fbt unitaire soit g\u00e9n\u00e9ralement plus \u00e9lev\u00e9.<\/p>

Les d\u00e9lais de planification habituels sont de 10 \u00e0 25 jours ouvrables pour les pi\u00e8ces standard, de 20 \u00e0 45 jours ouvrables pour les composants sur mesure et de 45 \u00e0 120 jours ouvrables pour les \u00e9quipements ou assemblages sp\u00e9cifiques \u00e0 un projet. Les incoterms EXW, FOB, CIF et DAP sont couramment pris en charge\u00a0; les incoterms FCA, CFR, CPT, CIP et DDP peuvent \u00eatre envisag\u00e9s pour l\u2019exp\u00e9dition.<\/p><\/div><\/div>Envoyer une demande de devis<\/a><\/div><\/div><\/section>","protected":false},"excerpt":{"rendered":"

Manufacturing and inspection planning for drawing-controlled spiral bevel gears and matched gear pairs.<\/p>","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"footnotes":""},"class_list":["post-486","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/spiralgears.top\/fr\/wp-json\/wp\/v2\/pages\/486","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/spiralgears.top\/fr\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/spiralgears.top\/fr\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/spiralgears.top\/fr\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/spiralgears.top\/fr\/wp-json\/wp\/v2\/comments?post=486"}],"version-history":[{"count":2,"href":"https:\/\/spiralgears.top\/fr\/wp-json\/wp\/v2\/pages\/486\/revisions"}],"predecessor-version":[{"id":571,"href":"https:\/\/spiralgears.top\/fr\/wp-json\/wp\/v2\/pages\/486\/revisions\/571"}],"wp:attachment":[{"href":"https:\/\/spiralgears.top\/fr\/wp-json\/wp\/v2\/media?parent=486"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}